16
Mar
Take 1 wheel off the trailer to access the hub assembly. Boat Trailer Wheel Bearing Kits.
This video walks you through how to repack change or replace your boat trailer bearings step by step.
Change bearings on boat trailer. This video walks you through how to repack change or replace your boat trailer bearings step by step. When to Change a Boat Trailer Wheel Bearing. The time period between boat trailer wheel bearings can vary depending on a few factors.
We always recommend at the very lease to check it during your spring boat service because as we reviewed earlier the boat trailer wheel bearing is put through the ringer every time your boat is put in and taken out of the water. Also how often should boat trailer bearings be replaced. We recommended to repack the wheel bearings on your trailer every 12 months or 12000 miles.
There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease you will also just want to check for any damage or wear and replace anything if needed. Take 1 wheel off the trailer to access the hub assembly.
Loosen the nuts on all wheels with a lug wrench while the trailer is on the ground. Jack the trailer up just enough to. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators.
Replacement Bearings for 7000 lb Dexter EZ Lube Axle to Have On Hand for Road Trip. Replacement Boat Trailer Hubs for 82655. Bearings and Seals for Dexter 3000 lb Axle with EZ Lube Spindles.
Axle Rating for Bearing 25580. Replacement 6-on-5-12 Idler Hub Kit to Replace Hub 82655. Replacement Bearings for Triton LTWCI-TX Trailer.
Move the tyre back and forth a few times by pushing the tyre with one hand whilst pulling back with the other hand. If there is movement also called free play in the tyre there is a good chance the bearings are damaged. Jack one side of the trailer up off the ground and remove the tyre.
Before jacking up the trailer loosen up lug nuts. This way the weight of the boat and trailer will prevent the tire from spinning. Jack the trailer up enough so that the tire you are working on can spin freely and place jack stand to support the trailer.
Remove the bearing buddy or dust cover. How Much To Replace Wheel Bearings On Boat Trailer. A lack of play will cause the bearing to heat up.
A loose worn or damaged wheel bearing is the most common cause of brakes that grab. A trailers wheel bearings are often neglected because they are out of sight. A wheel bearing is a small o shaped ring.
This video shows how to change the wheel bearings on a boat trailer. This includes removing the wheel the brakes and then the original races. We then go thr.
Bearings Seals for 2004 EZ Loaded Boat Trailer Using Bearings L68149 and L44649 Replacement Bearings Races and Seals for LM48548 Inner Bearing and L44610 Outer Race Recommended Brake Assemblies for Karavan Boat Trailer with 3500 lb Axle. Replacement Bearing Buddy for Boat Trailer. I have a boat trailer I lost my buddy protector I took the hub to a parts store he measured bore hole with a caliber he said it was 1 and 3 quarter I cant fine one do u know if they make them.
To pack a new or a reusable bearing squeeze out a palmful of new grease and scrape the bearing across the grease to force it into the edge of the bearing from the large end until it emerges from the small end making sure the grease works its way all the way through the bearing assembly rollers and cage. Boat Trailer Wheel Bearing Kits. Below are Trailer Wheel Bearing Kits for 4 Bolt Trailer Hubs 5 Bolt Trailer Hubs 6 Bolt Trailer Hubs and 8 Bolt Trailer Hubs.
These Wheel Bearing Kits come and complete allow you to replace your damaged wheel bearings and grease seals. How to Tighten the Boat Trailer Hub Castle Nut. To tighten the hub castle nut properly after having slid in the hub with rear seal and bearings installed tighten the nut as you spin the hub until it slows the hub from turning.
Next back off a quarter-turn and push on the sides of the hub to check for wobble.