14
Aug
This makes it difficult to tell when exactly is the right time to change your boat. Do Trailer Bearings Fit Tight To the Spindle they Install On.
I wonder if you could save me a two hour drive.
Change wheel bearings on boat trailer. The time period between boat trailer wheel bearings can vary depending on a few factors. We always recommend at the very lease to check it during your spring boat service because as we reviewed earlier the boat trailer wheel bearing is put through the ringer every time your boat is put in and taken out of the water. This makes it difficult to tell when exactly is the right time to change your boat.
How to Replace Trailer Wheel Bearings - YouTube. Today we list a quick do it your self guide on how you can replace and adjust wheel bearings to ensure optimal performance and reliability in your boat trailer. Place a jack under your trailer.
Jack the trailer up so the wheels are not touching the ground. Remove the wheel dust cap split pin axle nut washer. Take 1 wheel off the trailer to access the hub assembly.
Loosen the nuts on all wheels with a lug wrench while the trailer is on the ground. Jack the trailer up just enough to lift the wheels off. Uses 1 38 68149 x 1 116 44649 Bearings.
Replaces 5 Lug 3500lb Hub Bearings. Includes Wheels Bearings Races and Grease Seals. 1 116 in x 1 38 in Trailer Wheel Bearing Kits Uses Bearing Numbers 44649 x 68149.
To pre-load the bearings install the spindle washer and spindle nut onto the spindle with the hub and bearings in place. Tighten the spindle nut finger tight until snug and then with channel-lock pliers or a crescent wrench tighten the spindle nut another 14 turn or about 15 to 20 ft pounds of torque. Now turn the hub ten revolutions.
Replacement Trailer Hub Assembly for Dexter 8-248 Hubs. Recommended Idler Hub For Boat Trailer With 3500-Lb Axle. Replacement Hubs with 5-on-4-34 Wheel Bolt Pattern.
Replacement Hub for Master Pro PT A-4 and National Bearing A-17 Bearings on a Utility Trailer. Determining Correct Replacement Axle For Older Axle W LM29749 and L44640 Bearing. Swap the complete hubs for taper roller bearings they are quick and easy to change you can strip them down easily for cleaning also if needed you can change them at the side of the road with a jack and simple tools.
After towing every weekend for years then dunking the trailer in the sea from the beach it is the only way to go for. Process for Changing a Damaged Spindle on a Trailer Axle. Do Trailer Bearings Fit Tight To the Spindle they Install On.
How to Pick Out an Axle for a 6 x 12 Utility Trailer. Trailer Hub w6 Lug Pattern Inner Bearing Inner Diameter 15 Outer Bearing Inner Diameter 125. Is It Possible to Just Replace Trailer Axle Spindle if Axle is Still Good.
We recommended to repack the wheel bearings on your trailer every 12 months or 12000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease you will also just want to check for any damage or wear and replace anything if needed.
As long as everything looks fine there is no need to. How to Tighten the Boat Trailer Hub Castle Nut. To tighten the hub castle nut properly after having slid in the hub with rear seal and bearings installed tighten the nut as you spin the hub until it slows the hub from turning.
Next back off a quarter-turn. Move the tyre back and forth a few times by pushing the tyre with one hand whilst pulling back with the other hand. If there is movement also called free play in the tyre there is a good chance the bearings are damaged.
Jack one side of the trailer up off the ground and remove the tyre. I have an older Calkins boat trailer with 530 x 12 tires I need to replace the bearings and the trailer is at the lake. I wonder if you could save me a two hour drive.