How do you grease a boat winch

It is particularly suitable for lubricating heavity loaded sliding surfaces such as bogie pins on aircraft landing gear assemblies over the temperature range of -73 C to 149 C. Your trailer has an impact on how much your boat slides and therefore how hard your winch has to work.

- if you are doing the job on the boat take an old shoebox and cut a winch size hole in the bottom and put it over the winch this way you will be less likely to drop pieces overboard as the shoebox.

How do you grease a boat winch. In this tutorial Niel from Yacht Hermione shows how to dismantle and grease up a basic winch. Whilst this might look intimidating at first glance it shouldnt be. Taking your time and photographing along the way will help you put it back together in the long run.

Using a grease gun is also recommend for ease. Grease the main axle of the winch and the gears. Less is more here you dont want to cake on the grease just a light coat will do.

The roller bearings need a light coat too just a sheen on them actually. Put a little grease on your fingers and massage it into the gear races. The oil is reserved for the winch pawls and you only need a drop on each pawl.

You want the pawls to move smoothly and to. I took one of these winches off the boat the one that was beginning to seem stiff and slow to work and looked at a bunch of videos on YouTube about older winchesAnd carefully took this one completely apart. And then put it back together again without cleaning it or anything right away so that I know I can do it.

It is a lewmar 40 2 speed self tailing and unlike all the lewmar forties that. Ill probably go to a Tractor Supply Company down the street and see what they have. If not then across the street is Lowes and Home Depot that share a parking lot.

Another source of grease is used on outboard motors to lubricate where the lower unit shaft inserts into the crankshaft. Use his - or others - proprietary lubricant instead of garage grease use very little of it and - more important than anything else - stick the fresh water hose into each winch handle socket for a few seconds each time you fill up to rinse away the salt-laden water inside. Moly would work but for you Floater I think Id recommend something marine-rated.

If you dont know what was in it make sure you clean the old grease out well. Some grease bases dont cooperate well with others and IIRC few marine-rated greases use lithium base. Hang on lemme goggle.

Finally before the main housing goes back in place give all the gears and pins a light coating of grease. Most bearings are stainless steel and should receive a light coating of grease. If the bearings are plastic as youll find in some winches do not grease them as it will interfere with the winchs function.

Step 1 - Grease the Cable. Start by attaching the scrap fabric to the cable. This should be about 6 feet from the drum end of the cable.

Grease the cable by placing a shop rag in the marine grease. Wrap the rag around the cable where the winch will attach first. How To Use A Winch.

Winch operation is pretty simple too - after all it is a simple machine. You wrap the line around the winch three or four times from the bottom up pulling the line in with one hand and while you crank the winch with the other. On big boats or heavy breeze days you can team up on a winch with a crew mate where one person.

Learn how to properly grease a PS654 electric winch. Its important to grease replacement parts before installation or use. The grease prolongs the life of t.

Clean off dirt and grease. The small parts bearings the shiny roller ring thingies gears and pawls can be soaked in mineral spirits. Just about 5 minutes is all it takes for the mineral spirits to work their magic.

Reassemble lightly greasing gears and bearings. You can use WD-40 or oil on them if you want. How do you use a winch on a boat.

Beginning from the bottom of the drum wrap the rope around the barrel of the winch in a clockwise direction. Wind the rope around the drum three or four times. Insert the winch handle into the top of the winch and use it to wind the rope tight.

Remove the winch from the deck. You need to access the underside of the deck where the winch is located to remove the nuts and washers from the screws or bolts that hold the winch to the deck. You might need a helper to hold the fasteners from above while you work below.

Winch fasteners on the underside of the coaming. Always use fender oversize washers or a backing plate to distribute. Your trailer has an impact on how much your boat slides and therefore how hard your winch has to work.

If you are using rollers there is less resistance than carpeted wood bunks so a smaller winch will do the job. Regarding cranking resistance lighter boats can use a manual winch. The first few times you strip a winch its worth draping an old sheet over the rail to stop components being lost over the side of the boat.

Normally the only tools needed for winch servicing are screwdrivers and Allen keys plus small brushes to clean parts and reapply grease. Our shop will generally use WD-40 to clean de-grease and dissipate moisture. Namely in servicing a boats winches you can read more on that here.

It can also be used to remove clean up any excess sealant. Although you should have a can of this with your winch service kit Wd-40 can typically be left a-shore for the average club and buoy racer. Lubricating a Boat Lift.

For cable lifts use a marine-grade grease to lubricate bearings and pulleys. This task should be done every six months or so. Motors and their parts should be oiled using an anti-corrosion lubricant at least twice a year depending on use.

Grease for Warn winch. AEROSHELL Grease 17 is a fully synthetic grease containing 5 molybdenum disulphide. It is particularly suitable for lubricating heavity loaded sliding surfaces such as bogie pins on aircraft landing gear assemblies over the temperature range of -73 C to 149 C.

• only take apart one at a time - this way if you forget how they go back together you will always have a fully assembled winch to look at. - if you are doing the job on the boat take an old shoebox and cut a winch size hole in the bottom and put it over the winch this way you will be less likely to drop pieces overboard as the shoebox.