How do you lubricate a boat throttle cable

It clamps on the cable where the steel exits the plastic cover. Pour enough motor oil into the bag to fully submerge the end of the cable jacket and zip the bag closed.

These include the following.

How do you lubricate a boat throttle cable. How do you lubricate a boat throttle cable. Pour enough motor oil into the bag to fully submerge the end of the cable jacket and zip the bag closed. Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket.

Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket. Allow the cable to hang until the oil drains through. Slide and rotate the cable in the jacket then give the bag a second shot of oil it can be the same oil to assure a thorough lubrication.

Subsequently question is how do you lubricate an outboard throttle cable. Pour enough motor oil into the bag to fully submerge the end of the cable jacket and zip the bag closed. Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket.

Allow the cable to hang until the oil drains through. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. 1992 Johnson 60hp stupid question but how do you lubricate the throttle cable and with what seems to be sticky.

Steering cable has grease zerts so that one is easy. However I recommend lubricating it from the top down let gravity help you. Remove the fuel tank and seat so you can get to the carb.

Release the end of the throttle cable from the carb so you can take it in your hand and hold it up in the air so gravity will help you. Thankfully not much you dont have already. Prepare the Work Area.

Remove the Clutch Lever. Slip on the Cable Luber. Lube the Clutch Lever Cable.

Reinstall the Clutch Lever. Disassemble the Throttle Cable Housing. Lube the Throttle Cables.

There is such a thing as a cable luber. It clamps on the cable where the steel exits the plastic cover. You connect a spray can of cable lube via the little red straw and have at it.

My cable is actually splitting and pulling apart its bad. I will let you know how it goes. Are you sure their is no adjustment to make it throttle easier like a tension bar below it or anything.

You may be able to lube it at the linkage and you could always take the rubber grip off and clean and lube under it if the cable looks good. Remove the screws on the back of the housing with a screwdriver. Pull the remote housing away from its cover.

Apply a light coat of white marine grease to the throttle cable where the cable end enters the cables flexible metal casing. Press the release and remove the motors top cover. Set the cover aside.

How to lube a control cable with a cable luber tool - YouTube. What should I lubricate my throttle cable with. Push the throttle cable pin through the end of the throttle cable.

Lubricate end of the pin guides rollers helix halves and inner steering handle with Moly Lube 0175356. Can a broken throttle cable be repaired on a motorcycle. Secondly how do you lubricate a boat throttle cable.

Pour enough motor oil into the bag to fully submerge the end of the cable jacket and zip the bag closed. Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket. Allow the cable to hang until the oil drains through.

How do you lubricate a boat throttle cable. Pour enough motor oil into the bag to fully submerge the end of the cable jacket and zip the bag closed. Place a container beneath the bottom end of the cable to catch the oil that should eventually drip.

How To Lubricate A Cable - Prevent Cable From Freezing - YouTube. ANGLE 61 ALLIE PHVID3. If you want wrap a shop rag around each end of the throttle cable to capture any escaping lubricant.

For clarity my pictures do not show shop rags. Remove the spray can and Tool. Wipe up any excess lubricant and press the cable dust shield back into place.

I just did my first ML throttle cable lubrication today and immediately noticed. Directions for a Throttle and Shift Cable Oiler. You need a foot and a half of 38 ID reinforced plastic hose from Lowes a tire valve three hose clamps a tire pump or small 12 volt air compressor with a gauge and some MMO Marvel Mystery Oil.

Shave the tire valve down and clamp it in one end of the hose. The Basics On How To Lube Steering Cable On Boat. When lubricating the steering cable on your boat you will need to have a few things on hand.

These include the following. Stainless steel steering tilt tube. Nut with zerk fitting.

Once you have these things ready then you. There is no official way to lubricate the cable. It is possible to make up a system that will allow you to pump oil into the cable to lubricate it but its time consuming and not worth it on a throttle cable.