How to check boat engine hours

Boat hours generally translate to between 10 to 30 miles per one hour of use. You can do a test diagnostic and find out some data or even pull a head.

An outboard engine can run on an average of about 1500 hours.

How to check boat engine hours. How Do You Check Boat Engine Hours. Engine hours can be checked by looking at the hour meter for older engines. Engines built in the last 20 years will store the hours on the engine computer and can be read via the gauge or a diagnostic computer.

If the boat you are considering has a carbureted engine there is no engine management system to tap into so you there is really no way to verify engine hours. At that point if you really are interested in that particular boat you can either investigate further with mechanical inspections and compression and leak-down tests or you can wash your hands of the whole matter and look for a boat. If you have an engine hour meter read and record the number from the meters face as the first entry in the engine-hour log.

An engine hour meter automatically records the number of hours your boats engine operates in the same way an odometer records the number of miles your car moves. If you dont have an engine hour meter simply start your log with zero hours and add the total hours of operation each. I was wondering if there is any way to check how many hours are on my engine.

Your motor has a TB-V ignition and yes with the Rinda scan tool you can read engine hours and amount of time it has spent at preset rpm levels. Life Expectancy of an Outboard Inboard and Jet Boat Engines. It is important to be informed about your outboard boats engine capacity concerning how long it has before it finally gives out.

Many underlying factors affect the endurance of the motor such as maintenance type and age. An outboard engine can run on an average of about 1500 hours. They are normally found on the dash of the boat but sometimes are mounted under the dash or in the engine compartment.

Step 2 Read the hour meter from left to right. When buying a boat it is good to know how boat engine hours affect the used boat value. Always ask how many hours the engine has on it and dont forget to dr.

When I had a Df90. A few years ago now from memory for boats that dont have an hour meter on the rev counter the indication of the hours was done by the first 3 seconds when ignition switched on the rev counter will show the hours before starting engine. Again from memory per 100rpm indicated every 10hrs run so if rev counter goes 200rpm thats your first 20 hrs 500 rpm 50 hrs.

Most marine engine manufacturers recommend an oil change every 50 engine hours. Our 1000 hour boat serviced every 50 hours would have had the same 20 oil changes. Similar levels of wear can be assumed in this example.

Some newer vehicles have an engine hour meter. Here is a picture of the hour meter on one of our shop trucks. The meter can usually be found above the engine or somewhere around the steering area of the boat.

The numbers on the meter show how many hours the engine has been in use. If there is no hour meter one should be installed by a marine mechanic. There are three ways to check hours on a Mercury Outboardengine diagnostics a gauge on the boats console or an after-market engine hour meter.

Some boaters rely on the old-school method of pen and paper logging. For Engine hours click on Data Logger and then click on Engine Operating Hours according to engine speed If you wish to save the hours click F2 to save the file it saves as a csv file or a Comma Separated Value file and an xls filein a nutshella file Excel can read or most any data application like Notepad wordpad etc. If a boat has electronic fuel injection you can look in the engine management system.

This will give you a reliable record of the engine hours. An accurate representation of engine hours can be essential if you plan on buying a used motor. Boat Hours versus Miles.

Boat hours generally translate to between 10 to 30 miles per one hour of use. The average marine gasoline engine runs for 1500 hours before needing a major overhaul. The average marine diesel engine will run for more than three times that long and log an average 5000 hours under the same conditions.

The number of hours that a marine engine runs is very dependent on the amount and quality of maintenance over the years. Inspect the engine for an installed hour meter. The meter can usually be found above the engine or somewhere around the steering area of the boat.

The numbers on the meter show how many hours the engine has been in use. If there is no hour meter one should be installed by a marine mechanic. You can take it to a dealer and they will hook it to the buds system and tell you for a slight charge i assume.

Then buy a hour meter and install it yourself. Multiply the amount of hours on your engine by 60. Use the number you come up with to estimate how many miles are on your engine.

For example 1235 hours on an engine equates to approximately 74100 miles. Engine oil-life monitors that track engine hours rather than mileage take into account idling time rpm and other factors that aren. With inboard boats its recommended to change the oil every 50 to 75 hours.

So if there was a used boat for sale with 745 engine hours and it was routinely serviced it would have had 9 oil changes. Like the truck a boat with 745 engine hours has many years of optimal running performance left. In fact its just past getting broken in.

Checking the hours on yamaha with home computer I think I might have found a tach that gives me the hours trim oil and engine temp. It is yamaha part number 6y5-8350t-82-00 It is a digital multi function yamaha tach. I can get it for 25000.

Do you guys think it will hook up to my existing plugin. I have a yamaha model 703 throttle remote. This gives you an idea of how the motor was used - lots of trolling or lots of time at wide-open throttle.

A typical use pattern should show about 40 percent of the hours below 1000 rpm. And it might show for example that the motor was never run over 5000 rpm which is really odd. The total hours of operation for both style tachometers cannot be reset.

The operational hours on the Multifunction Tachometer are measured when the engine is running. The operational hours for the Command Link Tachometer are received directly from the ECU computer on the engine. Both tachometers have a trip meter function that can be reset.

Small plane engines must be rebuilt in the range of 1200-1600 hours depending on make and they are usually well maintained. You can do a test diagnostic and find out some data or even pull a head. Also you can put clean oil in it with new filter and run it several hours to see if it remains clean.

Also check old oil for any metal filings.