How to drive a boat onto a trailer

Tying up at the marina. Drive boat onto bunk a bit so front bow V is in bunk.

Petes best advice for avoiding danger when driving through the marina dont over-throttle.

How to drive a boat onto a trailer. Many boat owners dont know how to correctly and safely drive a boat onto their trailerThere are 2 main points to remember the first is confidence. In this part either you or the car driver must take a position on the trailer tongue to hook the winch rope or strap to the boats bow eye and fully load the boat onto the trailer. Fasten the safety chain after the bow is snug on the winch post.

The following is a simple method that works with any boat. Tie up your boat to the dock. Then attach a single long line to the bow and stern cleat.

Back the trailer down deep enough that you can float the boat most of the way onto the trailer. Using the line you can control the boat as you walk down the dock. Once youve positioned the boat correctly start driving toward the trailer.

Go in nice and slow. The moment the boat hits the trailer assuming you submerged it in the right way you should feel it smoothly grab the boat every time. Since you went straight the bottom of the boats nose should land on the winch post or stopper without issue.

Drive Boat On Trailer Go Fishing Solo how to video Boating Tips Safety Beginners Guide - YouTube. Drive Boat On Trailer Go Fishing Solo how to video Boating. Recovering a powerboat.

If you want to learn to drive your boat onto a trailer this is a great class to help you build confidence in putting your boat back on the boat trailer. Learn the following things. Petes best advice for avoiding danger when driving through the marina dont over-throttle.

Tying up at the marina. Driving your boat onto a trailer. Winds it on about a third of the way just pull the hull straight then I slowly use the engine to power.

Up the trailer making it easier for matewife to winch on. The trick is to let the winch pull the boat onto the. Trailer and not over run it with the motor.

The motor should just lighten the effort used to winch. Then drive the boat onto the trailer. If it wont go all the way to the winch post clip on the winch strap and winch the boat the rest of the way.

I just pull up to the dock put the trailer in the water use 2 dock lines and pull it right on the trailer hook up the winch usually takes less than 5 minutes i also have those trailer guides. The boat hit the trailer side arm and did not go onto the trailer. Accordingly the boat will be aligned with the support rails very early in the loading process as well.

There is also a steering wheel with which you can move the pontoon left and right. Carefully drive the boat onto the trailer. Back the trailer down deep enough that you can float the boat most of the way onto the trailer.

Using the line you can control the boat as you walk down the dock. Once the boat is over the trailer hop down and use the winch to pull it all the way to the stop. How to Load a Boat on a Roller Trailer.

The only difference is the wobble arm which is fixed. This component is designed for smaller boat trailers and hulls that do not need adjusting. Centre Adjustable Assembly The Centre adjustable assembly plays a crucial part in converting your boat trailer to a drive on system.

This component is designed to be installed around the centre of your trailer and aims to help guide your boat on and off your trailer. The trailer should be submerged with the bunks andor the rollers wet so that the boat can float up onto the trailer he adds. Once your car is in position put the emergency brake on and place chocks behind the wheels to keep the vehicle secure.

Holding the two ropes push the boat outward and then use the ropes to pull the boat slowly forward onto the trailer keeping it centered over the bunks. Once the boat hits the bunks attach the winch to the bow hook and winch the boat forward until it is securely tight against the bow roller of the trailer. Step two reverse the trailer down the ramp until the guards are approx.

12cm under the water. This will vary based a number factors size and model of boat trailer in addition to whether you are launching in a shallow ramp or not. Step three drive the boat slowly and carefully onto the boat trailer.

Step four climb over the bow. Retrieving Your Boat Onto a Trailer. Back the trailer into the water so that approximately two-thirds of the rollers or bunks are submerged in the water.

Set the parking brake of the towing vehicle and put it in park or first gear if you have a manual transmission. Drive boat onto bunk a bit so front bow V is in bunk. Driver slowly backs trailer into water as i add some moderate gas.

The boat moves onto trailer as the trailer moves under boat at same time. Half way up check to see if centered. Continue backing trailer as boat is powered up till the bow is tight onto bow stop.

Heres how to trailer a boat. Align the hitch and ball then lower the trailer hitch down over the ball. Close the latch and insert the safety pin.

Cross the safety chains and attach them to the truck. If your trailer has brakes attach the safety line to the tow vehicle. If your trailer has guide-ons the boat should settle into the proper spot on the trailer.

If not youll have to guide the boat into position by hand. Attach the winch line to the bow of the boat. Use the winch to pull the boat the rest of the way up onto the ramp and in position.

You can use either a manual hand-crank winch or an electric. The main reason we are providing this example of their drive on trailers is the modified glider kit flipper kit on their trailers. They are designed to perform the exact same job in helping to keep your boat centralized while driving your boat onto your trailer with ease.