14
Sep
So in case anyone is interested this is what I did to repair two rather big soft spots on my deck on each side where one mostly sits. From drilling holes and injecting closed cell foam to removing the wraparound and console and liftng the entire top from the drip rail up.
From drilling holes and injecting closed cell foam to removing the wraparound and console and liftng the entire top from the drip rail up.
How to fix soft spot in boat floor. We recommend tapping around the soft spot with the back-end of a screwdriver. If you hear a hollow sound youll have an idea if theres a weak area. When the sound becomes sharp and the material gives good feedback to the touch you know that its stronger.
You can use a grease pencil to mark off the affected area. Repairing the Soft Spot in Your Boat Floor. Probably slicing your boat is not something you really want to consider and for good reason.
However in some cases you will need to cut an inspection hole when you see soft spots on the boats fiberglass. Fiberglass delamination can be fixed by drilling small holes into the fiberglass surface of your boat. You can inject the materials you want such as resin or other.
How do you fix soft spots on a boat. Fiberglass delamination can be fixed by drilling small holes into the fiberglass surface of your boat. You can inject the materials you want such as resin or other fillers and a west system that dries and becomes solid rock protecting the fiberglass surface of your boat.
Soft Floor - Easy Fix. Or too much trouble. Given that you are just biding time I would say all you need to do is re-sheet it with 38 Exterior ply and throw down some cheap Home Depot IO carpet or Linoleum.
If the soft spots are really bad it might feel a little springy but you wont fall through. Spray foam is cheap and easy to spray onto the hull prior to installing the decking but it also absorbs water likewell. It will easily add up to a few hundred pounds to your boat.
Your boat will sit lower in the water than it was designed tothereby placing your outboardleg lower as well. Mistakes to Avoid When Repairing A Rotting Boat Floor. Repairing a rotten boat floor isnt too difficult.
However there are still plenty of things that could go wrong. If youre not careful you may end up doing more harm than good. For instance a lot of people are not going to clean the impacted spot before making the repair.
So in case anyone is interested this is what I did to repair two rather big soft spots on my deck on each side where one mostly sits. Put masking tape on the whole area and mark the area. Drill small holes about two to three inches apart in the whole area just through the top-layer of course.
Please like and or Subscribe to enable me to get some more videos and tutorials online. Im also looking for requests or ideas for the next great tutorialWWW. If it is a 2 piece hull youll need to remove the outboard and disconnect the wiring harnesses in most cases along with the steering and throttle.
Almost any and eveything attached to the top piece of a 2 piece hull has to be removed. Be able to seperate the hull and get it back to together. 3- for the repair itself.
61 2 9533 5470Email. Repairing a soft spot in a fiberglass deck is both a monstrous dance with reciprocating saws and grinders that cut into your boat and a precise ballet of blending chemicals cutting materials and applying them to the wound to produce a finished product barely distinguishable from the original. So finding a soft spot in the floor is frequently just the tip of the iceberg.
Now just because the wood and foam is a little wet doesnt mean the boat isnt safe just that at least its on the way to getting there. Anytime you find a boat with soft spots you should expect the worst because about 90 of the time its worse than it first looks. To fix soft spots with either Gorilla Glue or Foam Sealer you can follow these simple steps.
First locate the soft spot and find its outer edges. You can trace it out with a pencil if you wish. If you have multiple spots just trace them all out at one time.
Second drill holes using a. It was not long ago that I decided to repair a soft spot on the fly bridge of my F32. Being an adventurus fellow I pondered many different plans of attack.
From drilling holes and injecting closed cell foam to removing the wraparound and console and liftng the entire top from the drip rail up. Well I took a less invasive I THOUGHT route by cutting in to the outter skin of. Just The Floor Core Was Rotted On My Buddys Boat.
My friend asked for help with a soft area in his boat floor. We took a look at it and used a small hammer to thud test to see how far the rot went. There is a distinct difference in sound when you hit a solid floor versus one that has very little substance.
About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. Fill any voids in the surface of the putty wait 24 hours and sand again with 00 grit sandpaper. While you wait for the putty to cure cut the fiberglass sheeting to a size that will cover the repaired area and sister the repair strengthening the weak spot and providing the.
Once you pull the floor up you will need to check the stringers and transom which normally go with the floor. If the stringers and floor are solid cost and time will be drastically reduced. So lets be optimistic and say all you need to do is the floor.
This is a 300 way to revive a hull if it was a 23 1976 potter hull seacraft maybe do a 3000 floor. This is a solid answer for a few years or even more if you replace the wet pulp with foam as it rots away. It works over floor supports as floor supports wherever the old fiberglass skin exists.