Rolling with non skid particals is acceptable or you could spray the gelcoatnonskid for. Restoring your gelcoat can help restore the shine of your boat and protect its surface.
You could try one of those on your paint but be careful and test in an inconspicuous area first.
How to gelcoat a boat floor. Rough the surface of the floor with an orbital sander and 80-grit sandpaper. This gives the gelcoat something to adhere to. Wipe the floor again with acetone and a rag and allow it to dry thoroughly.
Wear gloves and eye protection at all times when handling acetone gelcoat or catalyst. Making sure that your gelcoat is applied evenly on the paintbrush go over the base of the boat beginning on one side and working your way over. Make sure that you give your boat a thick layer as a thin layer may not give a complete seal.
If available you can use a spray gelcoat. Surfacing wax is what you want to add to the gelcoat it will make it a breeze to clean the deck with the wax in it verses no wax in addition to it curing tack free. Rolling with non skid particals is acceptable or you could spray the gelcoatnonskid for.
Put down 1 coat smooth. Tape off an area that you want textured. Mix up some gelcoat with cabasol to a ketchup consistency.
Roll on to taped off area. You will end up with an intense orange peel effect. One recipe I have on spraying Gelcoat is.
Making Boat GelCoat Look Good. Apply the gelcoat using a brush if youre covering a small area. To apply the gelcoat with a brush dip the brush in the gelcoat so theres a liberal amount of gelcoat on it.
Brush the gelcoat onto the fiberglass using short vertical strokes. Avoid spreading the gelcoat too thin or youll get stroke marks. 10 mils gelcoat - little or no additives no surfacing wax 2.
10 mils gelcoat - little or no additives no surfacing wax 3. 10 mils gelcoat - with additives surfacing wax Allow the gelcoat to harden for several hours between coats. Applying gelcoat by brush - YouTube.
Applying gelcoat by brush. BoatUS Magazines Mark Corke shows you how to easily repair those pesky spider cracks that show up in your boats fiberglass gelcoat. While this may seem lik.
Step 1 - Getting a Gelcoat Stripper. Stripping the gelcoat from a boat deck has become such a popular practice that there is a special tool known as the Gelplane which effectively cuts the Gelcoat from the decking removing the need to worry about peeling it off slowly. You can find a Gelplane in most local stores or online.
This video is about Small Fiberglass Gelcoat Repair and the dilemma of using gelcoat over epoxy on boat repairs. It is not advised to do so but can be don. Gelcoat webbing boat floor.
Jump to Latest Follow 1 - 20 of 31 Posts. 1 of 2 Go to page. Joined Jan 15 2009 619 Posts.
Discussion Starter 1 May 15 2013. A good wash will ensure that your fiberglass has a smooth surface and therefore that the gelcoat will pour or spray evenly onto the boat. Once you have washed the fiberglass give the area where you will be pouring your gelcoat a good buffing with some sandpaper.
Im definitely not a fiberglass expert and most of my fiberglass experience has been structural transom replacement but this needed to get done so I thou. If the gelcoat starts to look transparent stop. After the surface has been compounded polish it then coat it with wax and buff it.
Providing the gelcoat has an adequate thickness your boat might have been compounded previously this process will restore the shine to fiberglass in almost any condition. For gelcoat the ZEP Heavy Duty Floor Stripper Concentrate or PoliOx as mentioned in the post or a boat store gelcoat oxidation remover work nicely. You could try one of those on your paint but be careful and test in an inconspicuous area first.
You also might ask at a paint store what they recommend or contact the paint manufacturer for info. In PART 19 on the Johnsen skiff build I Gelcoat the skiff along with webbing and non skid. This is a long video but I hope yall set back enjoy and learn som.
If you have some deep scratches clean them well and wipe them with acetone or rubbing alcohol. Make a putty out of white gelcoat and Cabosil then catalyze the putty and use it to fill the scratches. The Lavros look like cute boats and.
Over time and with use the gelcoat on your boat can become dull making your boat look old. Restoring your gelcoat can help restore the shine of your boat and protect its surface. Begin by making sure any surface dirt and stains are removed.
If your gelcoat is looking really dull with no bright or shiny spots youll need to apply polish first.