16
Sep
Steering Cable Lubrication Help The only thing you can lubricate is the steering rod. Special lube 101 is the best but any marine grease works pretty good.
And grease it an O-ring wipes all the grease off as it retracts into.
How to lubricate boat steering cables. With your grease gun lubricate the cable with the new grease fitting. Be sure to only use the recommended marine grease by the manufacturer. How To Remove Gas From Boat Fuel Tank in Quick and Easy Steps.
Important Things To Remember. This task of lubricating your steering cable involves dealing with power tools. Steering cable easy fixlubricate.
Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket. Allow the cable to hang until the oil drains through. Slide and rotate the cable in the jacket then give the bag a second shot of oil it can be the same oil to assure a.
Its lubed from the back by the rudder itself. Turn your wheel all the way in the direction that the cable is all the way out. One way it will be all the way in and the other way about 12 or so of the shinning cable will be sticking out.
Use a spray lube on the shinng cable that is sticking out. Then work the wheel back and forth. The best way I have found to lube it is to remove the cable from the boat and hang the cable from the steering head end.
A small funnel and plasticene can be used to hold oil at the top of the cable. You will notice that the cable inner has a spiral winding around its core. Steering Cable Lubrication Help The only thing you can lubricate is the steering rod.
Extend it fully and clean it. You may use a solvent if really dirty. Now lube it well.
Special lube 101 is the best but any marine grease works pretty good. Your motor should have a few zerc grease fittings. Hit those with a grease gun.
Tough steering so I started by greasing the three zirks identified in the owner manual using marine grease rudder post cable tube mount pivot cable tube. The zirk on the tube leaked grease zirk was loose. Tightened the zirk and the steering froze.
Always check your steer tube for adjustment the tendancy is to overtighten the bushing nuts and the steer tube must move ever so slightly back and forth to compensate for the swing of the tiller If the tube is too tight it will cause the steering to bind and be stiff A good working rack should be pinky finger operation out of the water Also having a swivel clevis about 20 bucksat. This helpful how-to video shows you how to ensure your outboard motor is maintained for peak performance. Here are step-by-step instructions for keeping your.
With all the other maintenance you do on your boat dont wait until the boats cable steering begins to tighten up before you lubricate the point where the steering cable interacts with the motor. Thread a piece of extra fine sandpaper into the rod from a firearm bore cleaning kit attach the rod to a drill and put the tube into a bench vice to hold it tightly. Arrow located on steering box center brass round piece points to center for centering steering wheel 2.
Both steering cables have same part number 3. Two methods to center steering noozles at rear of boat 3a. Strait edge across nozzles and square to rear of boat 3b.
Manual shows to measure the steering bar on nozzle distance away from. Just a little grease and light oil applied as demonstrated in this Mercury Quick Tip will not only help your engine have a long trouble-free life it will also ensure your steering is smooth and responsive every time you hit the water. The SafeT QC system is a three turn lock to lock steering package.
If your older system needed more turns the new one may feel harder to turn. You should also check that the cable does not have bends smaller then the recommended radius no kinks and that the steerer rod attachment to the motor is alligned correctly. Can you lubricate a boat steering cable.
Pull the steering cable out of the tilt tube. If the tube has internal corrosion that makes the cable difficult to remove liberally spray a water-excluding lubricant into the tilt tube and wait an hour before removing the cable from the tube. Just add my last service filters oil and gearbox oil on my Yam f 70 4 stroke was 150 which included less than 5 mins to lube the steering cable 5 mins 6-7.
The service before which inclided filters oil and impellor was 200. Edited May 15 2017 by JonD. And grease it an O-ring wipes all the grease off as it retracts into.
When I disassembled the system the steering rod was. Dry as a bone. While installing the new system I cleaned the tilt tube out with.
Engine cleaner and a wire brush. I then ran pieces of an an old. If the cable end comes out of the tilt tube and this fixes the problem then clean the tilt tube lubricate the cable end with marine grease and reassemble the steering.
Move to the Helm. Always replace steering cables that are stiff in operation or have damage to the plastic jacket outer casing. Clean and lubricate the engine tilt tube or cable support tube and the steering cable telescopic output ram as follows.
Remove the steering cables telescoping ram from the tilt tube. Clean the tilt tube inside diameter thoroughly. I attempted to lube my steering cable like that and i could not drill through the housing.
I spent over 30 min just trying to drill. Ended up replacing the cable myself and it was only 140 bucks wshipping. But if you really wanna give lubing a try you need something better than wd-40.
The best thing is ship to shore but a good alternate is liquid wrench. Drill into the cable under the dash.