19
Aug
How often should the Pledge be reapplied2. Next its time to lower the trailer on a very steep ramp.
Boat Trailer Bunks and Brackets are made up of bunk brackets that secure to the trailer frame using u bolts holding the bunk boards.
How to make boat trailer bunks. Place the boat on the trailer and make the necessary adjustments. After installing everything go over to check if everything was properly installed. Make sure that braces and brackets are all fitted tightly.
If everything checks out load the boat onto the trailer for the final adjustments. Check to see if the keel guides are placed properly. To fit a boat to the trailer make rough measurements to allow the boat to sit straight and level on the trailer then crawl under the trailer and position each bunk making sure that the bunks or rollers are positioned next to not under strakes or other protrusions from the bottom that the transom is well supported and that bunks are located under the interior stringers as well as any other areas needing.
For what its worth you can do a slick bottom coat that will make your boats hull corrosion proof AND make it slip off the bunks and debris super easy. Just remember if you do a slick bottom coat leave your boat hooked and locked to the crank or itll slide off the trailer. Start with the boat trailers front part by loosening the adjustable bunk brackets so that they can be raised freely.
When the boats front portion is resting on the bunk guide you can repeat the same process with the bunk brackets rear portion. When youve finished the first side of the boat you can do the same with the boats other side. If the installationadjustment has been done correctly the boat should be resting firmly on the trailer bunks.
I am thinking about using Pledge on my trailer bunks to make the boat slide more easially onto the trailerFor those who have done this I have a few questions1. How often should the Pledge be reapplied2. Has anyone used any other brand of spray furniture.
Install the guide poles at the rear of the trailer and adjust them in until they touch the rub rail. We like to install them a few inches foreward of the rear crossmember on the bottom of the aluminum I-beam with two u-bolts per guide pole. The view from the rear of your boat and trailer.
It is the best approach to set up boat trailer bunks instead of doing the reverse. Loosen the brackets and reposition the trailer bunks until the hull sits securely on the bunks. You can then fasten the screws using the recommended torque.
BEST thing to do. Go to the grocery store and get a box of Gulf Wax canning wax. Take a block out of the box and put it in a plastic sandwich bag.
The next time you launch your boat rub the wax all over the bunk carpet when you park your truck. Nevertheless theres a general guide. The trailer bunks should be resting about 13 from the bottom part of the boats hull.
This step requires you to start in the front of the boat trailer. Raise the brackets by loosening them so the bunks will lie on the boats hull. Back the trailer all the way in to wet the bunks then pull up until at least half the length of the bunks is out of the water.
You can always back it in a little deeper once you get the boat seated if its too much trouble to pull it the rest of the way up. That will solve your problem. Some boat trailers are equipped with rollers to ease the movement of the boat from the water onto the trailer.
Some boat trailers are equipped with flat carpeted metal pads called bunks to support the boat so it is not damaged by the trailer. Whatever the reason for replacing the rollers on your boat trailer. With your boat resting on your keel rollers you should be able to make changes to your boat trailer bunks without removing the boat from your trailer.
Your boats bunks will vary by boat manufacture as to were the trailer bunk guides will be resting. Put the Boat on the Trailer. Next its time to lower the trailer on a very steep ramp.
Make sure you do it on the steepest one that is available to you. This will ensure the bunks of the target are sticking out of the water just a little. In accordance with the target bunks put the boat on your trailer.
The process of re-carpeting your boat trailer bunk is pretty simple and you will need very few tools to complete the project including. Some fine grade sandpaper. A heavy-duty staple gun and staples.
Needle nose pliers or a screwdriver to help remove the old staples or screws. A utility knife to cut the carpet. Boat Trailer Bunks and Brackets are made up of bunk brackets that secure to the trailer frame using u bolts holding the bunk boards.