29
May
IMHO most store bought guide-ons are either to flimsy the wrong height and just plain horrible. They are ideal to have on all types of boat trailers to.
Then i cut a slight bevel on the front end of the pieces and lopped the top corner off the rear endsThese pontoon boat guide ons will help guide you towards the rear of your trailer and then gentlyThese pontoon bunk guides allow you to load your pontoon effortlessly onto your trailer.
How to make boat trailer guide ons. Super Easy DIY BOAT GUIDES for your Trailer. If playback doesnt begin shortly try restarting your device. Videos you watch may be added to the TVs watch history and influence TV.
Created some new trailer guide-ons yesterday using some basic materials from the local hardware store. My main goals for these guide-ons was. Make trailer more visible when there isnt a boat on it for retrieval Help hold the stern in place during moderate windscurrents when retrieving.
A couple of years ago he purchased some boat guides with angled posts made of galvanized 2 square steel tubing that mount on the boat trailer frame and support two horizontal bunks or pine 2x4 rails covered with indoor-outdoor carpet. However after installing these guides per the instruction manual it was obvious that they were not adjustable to the extent that would actually center the boat over the trailer. Prepare the materials and tools needed to make the boat trailer guide posts.
Having the materials at hand will lessen the time needed to assemble and set up the posts. Have an ample space where you can have the materials ready. Having it near the trailer is also a great option.
Being that it was a drive or float on trailer it never had a winch. Another trick I did as to mount an eight ft. PVC covered chain 1PVC from the center mount where the winch would normally be to the trailer frame on both sides of that mount so as to form a guide to direct the boat.
They center the boat on the trailer since I set them snug against the rub rail. These are very sturdy and the upper contact part is a roller not a flimsy flexible rub pole. The rollers will not scratch your hull or rub rail.
IMHO most store bought guide-ons are either to flimsy the wrong height and just plain horrible. I wanted something. I bought these made by Smith with the LED light for the posts and am very satisfied with the quality and sturdiness.
You could do the same on your own with thick wall PVC and a hacksaw providing you can successfully fabricate the metal support piece to bolt to the trailer. If you have a metal salvage shop in your area you may find what you need. Boat Trailer Guide Ons and Posts.
This is a comprehensive selection of not only Guide Pole kits but associated parts related to replacing and installing individual components. We have complete kits with Guide Poles PVC and mounting hardware and we have Guide Post and pole kits that do not include the hardware allowing for custom selection. I checked the WIDEST part of the boat and set the guides the thickness of my hand layed flat against the boat which is maybe 112 wider.
I also put self centering rollers for the keel. Took the axle out of the guide rollers and put never sees sp on the then reasembled them. Guide-ons are normally put towards the rear of the trailer but can be mounted in other locations.
To load the boat with guide-ons one person backs the trailer into the water. Another person drives the boat onto the trailer. The front of the boat is then attached to a rope that pulls the boat to the front of the trailer using a winch.
The guide-ons keep the boat centered on the trailer as it is being cranked forward. Pontoon trailer guide rails pontoon trailer guide rails boat trailer guide and auto latchPrepare the materials and tools needed to make the boat trailer guide postsRead more how to make your own diy pontoon boat inflatable pontoon boats. See more ideas about boat trailer boat trailer.
Roller guide ons mount to the trailer frame similar to the post style but they have 9 to 12 rollers attached to the brackets to guide the boat onto the trailer. All rollers are made of non-marking rubber to prevent scratches or damage to the boats surface. My boat that i boat had PVC guide ons and they work fine.
Except one thing is we drilled a hold in the top of both and ran a bungee across because when you are pulling the trailer the tubing will slap the side of the boat. Slide one 6-foot section of ¾-inch PVC pipe over the aluminum pipe to protect the boat surface when it rubs against it. Drill a hole through the PVC and aluminum pipe.
Insert bolt and tighten to secure the two pipes. Guide posts are L-shaped and available in different widths and heights. Most are 40 to 60 high.
They are simple to installjust attach them to the trailer frame with brackets and bolts provided and set them between the uprights a distance about 2 wider than the widest beam of the boat. Then i cut a slight bevel on the front end of the pieces and lopped the top corner off the rear endsThese pontoon boat guide ons will help guide you towards the rear of your trailer and then gentlyThese pontoon bunk guides allow you to load your pontoon effortlessly onto your trailer. They are ideal to have on all types of boat trailers to.
CE Smith Pontoon Boat Trailer Guide-Ons Pontoon boat trailer guide ons are a helpful tool to make it easier to load your boat onto your trailer and also help with backing the trailer into the water and getting your trailer in at the right depth. Check out this full selection of guide ons guide poles and accessories for your boat trailer. We have Galvanized and Aluminum components to complete or replace to make your boat trailer as functional as possible.
We have allot of options for your boat trailer. Below you will see several different styles of Guide. Then I cut a slight bevel on the front end of the pieces and lopped the top corner off the rear ends.
I then sanded both cuts making the rear into a rounded bullnose. I also planed and sanded down both top sides for the length of the boards so there were no sharp corners in contact with the hull of my boat.