How to prep fiberglass boat for bottom paint

Apply Bottom Paint Apply minimum of two coats of Sea Hawk bottom paint. If your boats new or has never been bottom-painted before get rid of any wax or residue by using a solvent like Interlux Fiberglass Solvent Wash 202.

How to Paint the Bottom of Your Fiberglass Boat - DIY - YouTube.

How to prep fiberglass boat for bottom paint. Scuff sand to a dull looking surface with 80-100 grit no finer sandpaper then rinse with water and allow to dry. If your old bottom paint is really chalky consider giving it a more agressive sanding to insure proper adhesion of the new bottom paint. Apply Bottom Paint Apply minimum of two coats of Sea Hawk bottom paint.

Allow 3 to 6 hours between coats and a minimum. How to Paint the Bottom of Your Fiberglass Boat - DIY - YouTube. It is important to get any such repairs made BEFORE you proceed to sand the bottom in preparation to paint.

This way any fiberglass repairs or patches can be faired before your paint. The repair may also need a barrier paint applied before you apply the bottom paint. Understand that the purpose for sanding is not to remove all of the existing bottom paint if any.

It is to create a surface which will allow better bonding. Some fiberglassresin matrices can absorb water over time often with disastrous results. Consider applying a barrier coating such as Pettit Protect 47004701 if you wet-store your boat to help avoid the problem.

Do this before applying the anti-fouling paint for the fiberglass boat. How to get your boat ready for bottom paint - YouTube. How To Apply Bottom Paint To Bare Fiberglass.

The following steps should be taken to insure good adhesion of bottom paint to a fiberglass or gelcoated hull. Premium Blister Protection and Adhesion System Best Paint Option. Sand to a uniformly frosty dull looking surface with 80-100 grit no finer sandpaper rewash with S-80 Wax.

Start by thoroughly washing the bottom with detergent and water and then rinsing well. Most manufacturers have a solvent wash or surface prep. Theres also soda-blasting which is more environmentally friendly.

But youll have to call in the pros. Plan on paying around 175 per hour. Prepping for Bottom Paint.

If your boats new or has never been bottom-painted before get rid of any wax or residue by using a solvent like Interlux Fiberglass Solvent Wash 202. Get the yard manager to move the stands as soon as the rest of the hull is dry never move stands yourself and put rags or sheet plastic on the pads to protect your new paint. Prep the bare spots and apply the appropriate number of coats.

Save a little paint to slap on the areas on the bottom of the keel you cant get to until the boat is lifted. How to Prep a Boat for Painting - YouTube. How to Prep a Boat for Painting.

If playback doesnt begin shortly try restarting your device. How to Paint a Boat - DIY Guide to Bottom Painting - YouTube. The below-laid procedure helps significantly in the successful painting of fiberglass boats.

Wear the eye goggles hand gloves and facemask to boost your safety during the painting process. Measure the boat from top to bottom and alongside this measurement will help further in painting calculation. How to Prepare your Boat for Painting a Gelcoat If the gelcoat is in good condition with no major cracking or crazing the job is relatively straightforwardclean and prepare the surface apply an epoxy primer sand the primer remove the sanding residue and then apply the topcoat.

The very first step is to thoroughly clean your boat. This is easiest to do shortly after you remove the boat from the water when its still wet. To ensure you get a deep clean you should use a combination of a pressure washer or high-pressure hose scraper and rags.

You should apply at least two coats of bottom paint. Each coat lasts about a year in the water. With two coats one coat will remain after a year and with no barnacle buildup your boat will be ready for another coat.

We applied four coats of bottom paint so that we do not have to pull the boat out of the water for awhile once we drop it back in. If you pull your boat out each year for the winter you. Boat expert Mike Gridley shows you how to get the colour back in your gel coat with a painting project.

He also shows how to change the colour accent in this.