13
Jul
If it does add more baking soda and let it dry. Remove the saltwater from your boat trailer after a day of fishing.
Leave more space than usual between you and the vehicle in front of you as braking is more difficult when trailering a boat.
How to remove boat from trailer. How to remove a boat from the trailer on land - YouTube. How to remove a boat from the trailer on land. If playback doesnt begin.
Easy way to Remove 19 Boat from Trailer on Land - YouTube. HOW TO REMOVE A BOAT FROM A TRAILER - YouTube. But if you own a aluminum boat this is a simple way to allow you access to work on your trailer without the use of machinery.
BE CAREFUL IF YOU TRY THIS. If your boat is on any incline the trailer will have a tendency to roll at this point. Be very careful when removing the wheel chocks and while pulling the trailer out so as not to have it jump right left backward or forward while safely guiding the boat trailer out under the Trapeze and between the two Stands and clear of the Boat Lift.
Lower the front of the trailer all the way. Raise front of trailer. Jack up bow of boat and block again.
Repeat until trailer is out. Block boat with jack stands to be safe. For at least one safe way to remove your boat from your trailer.
Lifting a boat from a trailer to paint the bottom detail or wax or to do any repairs maintenance adding of accessories to either your boat hull or trailer or for whatever reason you would need to have unimpeded access to your hull or trailer the G G Portable Boat Lift has. Former owner forgot to pull the plates off his boat trailer after selling it to a new owner bound for Florida but canceling the registration can be done through the DMV website. An effective and inexpensive coating that must go onto your boat trailer after every boat ride is fresh water.
Spray the trailer thoroughly with water from you home garden hose almost immediately after leaving the salt water. This method only works if you live or store your boat a few minutes away from the sea. The fresh water washes the salt away before it can damage the trailer.
Replace rusted parts before they ruin other parts of the trailer. Our installer here will spray the light with some lubricant around where the light meets the grommet and then will use a screwdriver to pry the light out first and then the grommet. If you check out the install video I attached you will see this done.
Helpful Expert Reply. Cap nuts like the part CE10801 are best removed with a pair of pliers to pry it off. Since these are intended to be used only once you need to make sure you have some replacements handy for when you need to put them back on.
This part is for a 58 roller shaft. Dig into your pantry mix some baking soda and water into a thick paste. Apply the paste it shouldnt run.
If it does add more baking soda and let it dry. Then use a brush to remove the paste and rust. For small or hard to reach areas as might be found on a trailer spring a stiff toothbrush works better than you might think.
Removing the leaf spring would certainly limit the load carrying capacity of the trailer and may soften the ride as you want but would be a permanent change. My recommendation is to try lowering the air pressure by 2 lbs at a time until you find the ride you are looking for. Heres how to trailer a boat.
Align the hitch and ball then lower the trailer hitch down over the ball. Close the latch and insert the safety pin. Cross the safety chains and attach them to the truck.
If your trailer has brakes attach the safety line to the tow vehicle. Take 1 wheel off the trailer to access the hub assembly. Loosen the nuts on all wheels with a lug wrench while the trailer is on the ground.
Jack the trailer up just enough to lift the wheels off the ground. Finish unscrewing the nuts on 1 wheel with the lug wrench remove. Extend the trailer jack to support the tongue and remove the bottle jack Diag6.
The boat should be well supported and stable on all three columns and the bunks of the trailer should be about 6 to 8 inches lower than the bottom of the boat. This will give you clearance to clean and polish the areas normally supported by the bunks. How to Protect Boat Trailer from Salt Water.
Remove the saltwater from your boat trailer after a day of fishing. For a nominal cost you can construct an effective rig to rinse the underside of your trailer using a garden hose a Y valve two lawn sprinklers and a PVC pipe. Select a spot thats level fore to aft and side to side and does not block any areas you might need to access.
Avoid overhangs that might dump snow water or ice on the boat cover. The trailer will be supported at five points with four jack stands and the tongue jack. Leave more space than usual between you and the vehicle in front of you as braking is more difficult when trailering a boat.
If wind sways your trailer or vehicle take your foot off the accelerator but avoid braking. Do not remove the winch strap or safety chains until you have got the boat into the water. Otherwise the boat can slide off the trailer.
Finally practice makes perfect. Be patient and give yourself some extra time loading driving and unloading your boat. EZ Lube Dust Caps like DC200L-DCRP have a rubber plug that can be removed to access the zerk fitting.
The rubber plug can be removed by gently prying it up with a flathead screwdriver. If your dust cap is in good condition and you want to avoid getting dents in the cover you can use the Dust Cap Driver Tool to remove the cap.