How to remove boat steering cable

Remove Your Boat Steering Cable Removing your steering cable is relatively easy. Simply disconnect the cable from the steering helm and from the engine using a wrench to loosen bolts that are holding it.

Then work the wheel back and forth.

How to remove boat steering cable. How to Remove Boat Steering Cables - YouTube. This involves removing the old cable removing the steering wheel and helm and installi. In this video I replace a Teleflex SeaStar steering cable and helm.

Remove Your Boat Steering Cable. Removing your steering cable is relatively easy. Simply disconnect the cable from the steering helm and from the engine using a wrench to loosen bolts that are holding it.

Next find a rope that will be used to assist you in pulling the cable back through the boat. Click here to know more about it. How can you remove the steering cable without removing the motor.

Hold on there a minute. I just went through this. Do not loosen that nut or the one on the opposing side.

The only nut you looseen is the chrome one thats attached to the steering cable. If you push that tube through your motor WILL fall as that holds it in place. You measure the plastic jacket end to end but in this case you add 30 inches and then round up to the nearest foot again.

For a new steering system installation on a stern drive application youre going to need to have three dimensions to get the cable length correct. Remove Your Boat Steering Cable Removing your steering cable is relatively easy. Simply disconnect the cable from the steering helm and from the engine using a wrench to loosen bolts that are holding it.

Spray the inside of the tube and the steering cable that passes through the tube with carburetor cleaner to break down the grease and particulates that may hinder your removal of the steering cable. Knock the cable out of the steering tube with a punch and a hammer. The ends of the steering cables ie.

The push rods are attached to the link rod which pushes on the engine causing the boat to turn. So I removed the bolts securing the push rods to the link rod and then went to the other side of the engine and loosened the big retainer nuts at the end of each cable. For outboard boats under 25 feet you can expect a replacement steering cable to cost under 130.

Teleflex systems are particularly effective where the installation requires long cable runs andor multiple bends between the helm and the engine. A stiff plastic jacket protects the inner cable in the core. Remove the nuts 3.

Twist until cables come out. Remove steering wheel and helm. To Release the outboard side.

Remove the connection to steering arm Photo 2. Remove the two nuts 3. Remove the bolt on attachment in photo 3.

Anything else I need to pull off to get the entire steering system off the boat. It depends on your model of boat as too how hard of a job it is. You need to disconnect the two cables on the port side and then the large nuts on the starboard side of the motor.

If you are able to get the old cables all of the way out of the motor without kinking them then you should be able to get the new ones in. Make sure you turn your wheel all the way left before disconnecting the old cable from the rudder and tie a rope on the end before you pull the old one through. This makes it easy to tie to the new cable and pull it back through.

There is like 3-4feet under the steering wheel that the cable runs you cant see or get to so the rope trick helps a. Replace the steering cable if the cable nuts on both ends are tight. Remove both cable nuts and the old steering cable and sheath leaving the old mounting brackets along the side of your boat in place.

Install the new cable using the old mounting brackets and tighten both cable nuts. If the cable end comes out of the tilt tube and this fixes the problem then clean the tilt tube lubricate the cable end with marine grease and reassemble the steering. Move to the Helm.

If the problem persists then move to the helm. Disconnect the rack or remove the cable end from the rotary gear. No the steering wheel does not move at all and the cable is fully withdrawn into the tube except for about an inch and it does not move.

If you remove the nut from the tube on the side of the motor with the outer covering of the cable then the outer covering will slide away from the motor and tube. Use an adjustable wrench to loosen the washer-head bolt in the steering link rod fastener. The washer-head bolt is located on top of the steering link rod fastener at the end of the steering cable attached to the engines tilt tube.

Ok the most likely problem is the cable is bad and will need replacing but lets disconnect the cable from the helm firstYou will have to take a pic of the helm under the dash for me to know how to remove the cable. There are many types of steering. Here is a couple of pics on removal of the cable for the most common helm used.

To remove or install the steering cables that control the Mercruiser sterndrive you must first disconnect the cable at the power steering unit then disconnect the other end of the cable from the steering flange on the sterndrive itself. The installation and removal is fairly straightforward as long as you know the. Turn your wheel all the way in the direction that the cable is all the way out.

One way it will be all the way in and the other way about 12 or so of the shinning cable will be sticking out. Use a spray lube on the shinng cable that is sticking out. Then work the wheel back and forth.