09
May
Replacing a boat steering cable can be challenging but its a repair that is totally doable for the mechanically-inclined boat owner. For a new steering system installation on a stern drive application youre going to need to have three dimensions to get the cable length correct.
Also on your new cable grease it really good before you install it to the rudder.
How to replace boat steering cable. Boat Steering Cable Replacement Guide - YouTube. Boat Steering Cable Replacement Guide. If playback doesnt begin shortly.
Replacing a boat steering cable can be challenging but its a repair that is totally doable for the mechanically-inclined boat owner. Inspecting Replacing Your Boat Steering Cable - Marine Parts Source. Before you pull the old cable out of the boat attach a messenger line at the steering wheel end so that when you pull the old cable out from the engine end you will have threaded a messenger to help install the new replacement cable.
Watch the video below to see some of the details. This article will help you change a steering cable with a Teleflex rack system. This will only cover changing the steering cable and not how to remove parts of the interior and flooring to get to the steering cable as there are a lot of different boats that this same procedure will work on.
Tools needed for the swap are as follows. The Basics On How To Lube Steering Cable On Boat. When lubricating the steering cable on your boat you will need to have a few things on hand.
These include the following. Stainless steel steering tilt tube. Nut with zerk fitting.
If the cable end is impossibly stuck in the tilt tube it is time to phone a friend and seek professional help. If the cable end comes out of the tilt tube and this fixes the problem then clean the tilt tube lubricate the cable end with marine grease and reassemble the steering. Move to the Helm.
You measure the plastic jacket end to end but in this case you add 30 inches and then round up to the nearest foot again. For a new steering system installation on a stern drive application youre going to need to have three dimensions to get the cable length correct. Always replace your boat steering cable with the same type that had been originally installed.
Rack with rack hydraulic with hydraulic and rotary with rotary. This way your craft will continue to handle as well as it did the first time you took her out on the water. Replacing steering cable on an inboard boat.
Start date Jun 28 2004. Codyandamber Petty Officer 2nd Class. Joined Apr 5 2003 Messages 106.
Jun 28 2004 1 I have replace steering cables on IO before but never on an inboard. I have an 85 mastercraft and the steering is tight. I do not see the part number on.
Simply disconnect the cable from the steering helm and from the engine using a wrench to loosen bolts that are holding it. Next find a rope that will be used to assist you in pulling the cable back through the boat. Tie a rope to the helm end of the cable then pull the cable through from the engine end.
Attach the new cable to the helm and insert the cotter pin to secure the connection. Run the new steering cable along the same path that the old cable followed to the tilt tube. Liberally apply marine grease to the end of the new cable and push it through the tilt tube.
Thread the 916-inch nut back into place and tighten with an adjustable wrench. Firmly press the injector fitting of your grease gun onto the boats steering cable nipple grease fitting and squeeze or pump the grease guns handle in order to generously lubricate the steering cable. Keep pumping the grease until it oozes out around the guns injector fitting and the nipple.
May 25 2010. Teleflex Steering Cable Removal- Rack Type. This is for the older type of cylinder remove steering end pinloosen this nut and give it a hit with a hammer to loosen it from the tapered shaft remove nut remove cable and tube.
This link is for the new style assist. Order that length cable. For Rack Steering Cable Replacement.
Measure Existing Cable as follows. Measure plastic cable jacket Y dimension shown in above drawing in inches add 30 and round up to next foot. Order that length cable.
For JBS Jet Boat Cable Replacement. Measure Existing Cable as follows. Measure old cable from tip to tip.
There is like 3-4feet under the steering wheel that the cable runs you cant see or get to so the rope trick helps a lot. Also on your new cable grease it really good before you install it to the rudder. You can push it in and out several times regreasing with a marine grade grease.
It will help the long term life of the new cable. Remove the steering cable from the tilt tube. Clean the tilt tube inside diameter thoroughly.
Remove corrosion in the tilt tube with a wire brush. Wipe until all loose material is removed. Lubricate the tilt tube with a good water-resistant grease.
Scour the steering cable telescopic ram with a brass wire brush and wipe until clean. Engine control cables should be replaced when at first signs of hard shifting sticky or slow response cable jacketing is chafed or cracked. Best policy is to replace them if they are older than ten years or when replacing your boat engine controller.
Control cables come in different lengths and we provide how to measure for correct length. Length is important and when measuring you need to include bends and. Having said that everyone who has ever had a boat with cable steering knows that at some point you will have to replace the cable.
I would think there would have to be some way to design the routing of the cable to make it to where you wouldnt have to pull the motor to remove and replace the cable.