How to replace boat trailer bunks

In order to replace your old carpet boat trailer bunks and replace with plastic bunk guides you will need to remove them from your boat trailer. After a thorough examination if you feel the need to change the carpet as well as several other things then you may need to change other things as well.

So what should I be using for lumber for the new trailer bunks.

How to replace boat trailer bunks. Remove the old bunks from the trailer while the glue is drying and measure the holes where either bolts or lag screws hold them to the trailer. Make sure you know how big your new hardware should be but also where the fasteners sit in proximity to the ends of the bunk. Write these down for reference and then transfer them to your new replacement.

How to replace boat trailer bunk boards and carpet on a Shore lander trailerRecently we discovered the bunk boards on my boat trailer had rotted and were ca. Step 1 Remove Existing Boat Trailer Bunks. In order to replace your old carpet boat trailer bunks and replace with plastic bunk guides you will need to remove them from your boat trailer.

In most cases you can simply unscrew your bunks form your brackets to lift off. Replacing trailer bunk boards. While the boat is on the trailer very carefully use a floor jack or a couple bottle jacks and lift the boat enough to take the pressure off the bunks.

Dont try and lift too high just enough to be able to remove one bunk at a time. Made a trough out of a poly tarp that would fit the planks. Put the planks in the trough and then poured enough Thompsons water seal to cover the planks.

Let it soak for a week or better. Then took the planks out and let them airsun dry. Salvaged the remaining Thompsons and used it on my back yard deck.

One approach is to first build the replacement bunks then tow the boat to the launch ramp pull the boat off the trailer and tie it up as you swap out the old bunks for new ones in the parking lot if permissible. 1 out of 5. 1 hour per bunk.

If you have a swing keel raise the keel completely off the trailer until youre finished replacing the bunk boards. Jack the entire trailer up one corner at a time and support the entire frame on jack stands to keep it stable. Mark the location of the front and rear edge of each roller onto the frame with a china marker.

Remove the nuts and lock washers using an adjustable wrench from the bolts that hold the rollers in place. Lift the bolts from the rollers. Lift the rollers from the trailer.

Repeat for all rollers. The boat trailer bunk is not where someone sleeps but what the boat rests on when on the trailer. You will find a boat trailer bunk on each side of the trailer and at each end.

They keep the hull of the boat safe. Over time the padding can become worn and ineffective. You can easily replace the padding and the following article will show.

Take Measurements Of Your Trailer Bunks. So we can apply the correct size marine carpet to your bunks we need to get the correct sizes. Start by measuring the length and width of the timber and take notes.

Add approximately 50mm 2 Inches to the length. Multiply the width by 2 add a further 50mm or 2 inches. The same goes for the bolts and other hardware used for securing the bunks to the trailer frame.

Reuse the parts if possible to ensure a solid secure fit. If you dont have the time or skills needed to replace the bunks you can have the work performed at your nearest Bass Pro ShopsCabelas Boating Center. Jan 30 2016.

Another option is to lower the tongue all the way to the ground. Then you can stack cinder blocks on both sides - place them under the horizontal surface below the black on your boat. Then raise the tongue back up - the boat will sit on the blocks rather than the rear bunks.

Now you can get bunk boards covered by slick plastic-type surfaces with Teflon or similar material. If it becomes less slick periodically apply Teflon or a similar lubricant from a spray can. If the cover becomes damaged its easy to get a new.

How to re-carpet your boat trailer bunk Step 1. Strip away the old carpet and remove any remaining staples or screws that were holding down the old carpeting. Once the wooden bunks are revealed inspect them for any signs of damage or rot and replace them if necessary.

Replace any old rusty hardware as well if necessary. Be sure to take the parts with you to the. First check the bunk of your boat trailer.

First you have to check your boat trailer to see if you just need to change the carpet or if you need to change anything else. After a thorough examination if you feel the need to change the carpet as well as several other things then you may need to change other things as well. To install the boards you will need a pair of Bolster and Swivel Bracket Assemblies CE10001G-4 per board which are 11 as well as a pair of U-Bolt Kits CE15283GA-4.

Ive added links to video reviews of these parts for you to check out as well. Helpful expert reply by. I have an early 90s 28ft Harris pontoon on a Bobcat trailer that needs the bunks replaced.

I recently found out first hand of the corrosiveness of pressure treated lumber with aluminum. So what should I be using for lumber for the new trailer bunks. Planning on using 2x6.

Should I be buying.