Pontoon boat steering cable replacement

When replacing the steering system on your pontoon boat you will need the following measurements to determine the cable length. At some point in every boats life if it has mechanical steering youre going to have to replace the steering cable.

Cable routings such as those found on pontoon boats may vary from this drawing.

Pontoon boat steering cable replacement. Our steering cable started to become very stiff. We eneded up replacing the entire cable which made a HUGE difference. EnjoyIf you enjoy the content and wan.

Watch this boat steering cable replacement guide. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new. How to replace the steering cable on a 21 pontoon boat.

If the cable itself is the problem you will need to replace the cable as there are no working methods to repair it. To check the cable loosen the nut at the motor end of the cable completely. Simply disconnect the cable from the steering helm and from the engine using a wrench to loosen bolts that are holding it.

Next find a rope that will be used to assist you in pulling the cable back through the boat. Tie a rope to the helm end of the cable then pull the cable through from the engine end. Replacing a boat steering cable can be challenging but its a repair that is totally doable for the mechanically-inclined boat owner.

Inspecting Replacing Your Boat Steering Cable - Marine Parts Source. Measuring For Your Steering Cable. When replacing the steering system on your pontoon boat you will need the following measurements to determine the cable length.

Measure from the center of your pontoons console to the edge of the starboard side of your deck. Teleflex Steering Rack and Cable Assembly The Teleflex SSC124 series is the replacement steering rack and cable for 1984 - 1996 era rack and pinion steering systems. This assembly does not fit the new style Back Mount steering systems.

If the steering wheel moves freely but the cables motor end does not move then look for a stripped gear at the helm. There will either be a bare spot in the rack or a stripped gear on the steering shaft. If there is a bare spot on the rack you will need a new cable.

If it is on the steering wheel shaft replace the gear. 1st things 1stMake sure you need a new steering cable. On a 20 Landau I believe you will have to unbolt the engine from the transom to get the cable out of the steering tube.

Once you have done this turn the steering wheel with out cable in the tube you may find it turns easily. In that case you just need to clean the tube. Mophorn Outboard Steering Kit 16 Boat Steering Cables 16 Feet Boat Steering System 34 Shaft for Boats.

42 out of 5 stars. Mophorn Outboard Boat Steering 13 Boat Steering Cable 13 Feet Outboard Steering kit. Boat steering cable replacement cost at a dealership will run you anywhere from 300-650 depending on the make and model of your boat.

However many folks opt to do it themselves as the boat steering cable replacement job is relatively easy. If you do go the DIY route for your marine steering cable replacement you can find the best and usually cheapest. Disconnect it at the engine.

Remove the steering console snake the cable out and youll be rid of the whole steering system. Then upon reinstallation youll just have the one hookup at the engine. Order that length cable.

For Rack Steering Cable Replacement. Measure Existing Cable as follows. Measure plastic cable jacket Y dimension shown in above drawing in inches add 30 and round up to next foot.

Order that length cable. For JBS Jet Boat Cable Replacement. Measure Existing Cable as follows.

Measure old cable from tip to tip. For Rotary Steering Cable Replacement Measure Existing Cable as follows. Measure plastic cable jacket Y di men sion shown in.

Cable routings such as those found on pontoon boats may vary from this drawing. Confi rm length by laying a garden hose or similar object along cable path and measure run from wheel to. Outboards without power steering.

No feedbackZero Torque mechanical steering BayStar or SeaStar hydraulic are recommended as replacement steering for all non-power-assisted outboards. For high performance boats or other applications in which there may be engine flutter or some steering instability dual cable NFB 42Pro Rack mechanical. Measure the plastic cable jacket of the previous cable in inches then add 18 inches.

The final result should be rounded to the next foot. Rack Steering Cable Replacement. The first step is the same with a rotary cable but you have to add 30 inches.

Also you have to round the final sum into the succeeding foot. At some point in every boats life if it has mechanical steering youre going to have to replace the steering cable. In the case of this particular cable that I have in front of me its from a rotary helm and once you take the cable off the boat if you look at the engine end of the cable on the plastic jacket youll find part numbers.

So my cable broke on the first turn of the season. I have it on a small 16 pontoon boat. It is a teleflex type steering but Im not sure if it actually is a teleflex or another make.

Ive never worked on the steering system before as it has worked flawlessly for the 10 years Ive had the. A replacement is the only solution to this concern. Owning a boat is fun but can be a lot of work.

Yet never delay the need to lubricate your cable steering as part of the maintenance process. Otherwise salt water or salt spray may penetrate the steering link arm and tube which can cause problems when you steer the boat.